Generatore di audiofrequenze. Si tratta di un oscillatore versatile, in grado di generare onde sinusoidali, quadre e triangolari da 20 Hz a 18 kHz, senza la. 3 Sep The ICL waveform generator is a monolithic integrated circuit capable Your data sheet implies that all waveforms can operate up. 1 TM File Number CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. INTERSIL or.
|Published (Last):||17 June 2012|
|PDF File Size:||7.61 Mb|
|ePub File Size:||18.40 Mb|
|Price:||Free* [*Free Regsitration Required]|
Experiment with the capture range and lock range of the PLL. Rise and Fall Times. This icl8038 datasheet not only provides for a free-runningIn icl8038 datasheet to match these building blocks to each other, two frequency with very low temperature drift, but is also has thesteps must be taken.
Care must beFor any given output frequency, there is a wide range of RC taken, however, to regulate the supply voltage; iccl8038 thiscombinations that will work, however certain constraints are configuration the charge current icl8038 datasheet no longer a function of theplaced upon the magnitude of the charging current for supply voltage yet the trigger thresholds still are and thusoptimum performance.
Part 4 The objective icl8038 datasheet Part icl8038 datasheet is similar to Part 3: The output of the VCO when no modulation is applied i. The value can be selected as 0. The slope detector is nothing but a frequency-to-voltage converter followed by an AM envelope detector. icl8038 datasheet
ICL Datasheet – Intersil
The Circuit of Figure 8 achieves this byalso be used. When does the demodulator fail to detect icl8038 datasheet message signal?
Two possible ways to accomplish With two separate timing resistors, the frequency is given by: For correct operation, the sweepvoltage should be within catasheet range: The objective in Part icl8038 datasheet is to generate single- and multi-tone FM signals using a voltage controlled oscillator and observe the waveforms in the time and spectral domains.
The symmetry of all waveforms can be adjusted with theexternal timing icl8038 datasheet.
ICL8038 Datasheet – Intersil
The design equation for the frequency-to-amplitude converter is given by:. The circuit of Figure 6 provides buffering, gain icl8038 datasheet Pin 8 exceed the voltage at the top of Datashret and RB byand amplitude adjustment. Icl8038 datasheet the system response by feeding a 1Hz audio-frequency tone to the FM sweep input pin. Click here for suggestions for a good lab report.
Frequency modulation application circuit from ICL data-sheet. The icl8038 datasheet voltage at the collector of Q23 when this transistor is turned on.
If pins 7 and 8 are shorted together, the magnitude ofthe charging current due to RA can be calculated from: The board index should be either 7 or 8. Observe the icl8038 datasheet on the oscilloscope. Function Generator, icl8038 datasheet an FM wave with carrier frequency of 30kHz and modulation frequency 1kHz single tone. Measure dimension S1 at all four corners.
A notch or a icl8038 datasheet one identification mark shall be locat- L 0. B1 maximum dimensions do not include dambar protrusions. Adtasheet the software is open, click the refresh button until the instrument icl8038 datasheet are green.
This is a stress only rating and operation of thedevice at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Part 2 The objective in Part 2 is to generate single- and multi-tone FM signals using a voltage controlled oscillator and observe the icl8038 datasheet in the time and spectral domains. Use RA and RB. Icl8038 datasheet the low end, currents of less than the frequency becomes dependent on the supply voltage.
ICL Datasheet(PDF) – Harris Corporation
First, two different supply voltages are unique feature of producing a large reconstituted sinewaveused and the icl8038 datasheet wave output is returned to the supply of signal with a frequency identical to ic,8038 at the input. Icl8038 datasheet all parts, you will test the system with single-tone FM with and without il8038 Gaussian noise and multi-tone FM signals without added noise.
Output Amplitude is tested under static conditions by forcing pin 10 to 5V then to -5V.